Revolver cleaning
#188103
12/30/2017 10:38 PM
|
Joined: Jul 2017
Posts: 9
InTim
OP
stranger
|
OP
stranger
Joined: Jul 2017
Posts: 9 |
I'm would like to know what the experienced revolver shooters rely on (products, tools and procedures) when they clean their guns?
|
|
|
Re: Revolver cleaning
[Re: InTim]
#188109
12/31/2017 12:48 AM
|
Joined: Nov 2015
Posts: 746
cherokeetracker
old hand
|
old hand
Joined: Nov 2015
Posts: 746 |
I like to use "Eliminator" since it does not smell so strong. I use the "Special Line" Dewey brushes from Brownells, since they fit on my "Dewey" Rod. I shoot 45 caliber mostly so I got a 50 caliber brush from Cabelas for the chamber only. I do use Tetra for when I shoot copper jacketed bullets. And or, Butches Bore Shine, is another good one.
I have not had to do this in a long time since I have not experienced any leading. But when I did,, I used a "choreBoy" copper scour pad, cut a small piece and wrapped and old brush to scour out the lead.
I do hunt west Tx some and it gets very dusty. SO I use a small paint brush to remove dust from the gun. then clean barrel and cylinder. The I lube the ratchet and base pin on Single actions. and Lube accordingly on the others. I use "Shooters Choice" red lube in a tube. Good quality lightweight oil where needed. But if I am going to a range session only,, I have been known to use a small amount of "Never Seize" It will withstand heat and beatings of the Big Bores. And resist wear on slides.
Collectors is a good oil to use for long term storage. I never tried any wax such as the Renaissance Wax.
Last edited by cherokeetracker; 12/31/2017 12:50 AM.
|
|
|
Re: Revolver cleaning
[Re: cherokeetracker]
#188486
01/10/2018 1:44 AM
|
Joined: Jul 2017
Posts: 9
InTim
OP
stranger
|
OP
stranger
Joined: Jul 2017
Posts: 9 |
Thank you for putting in the time for a detailed answer. The oversized brush for the chamber only is something I hadn't thought of but plan on using
|
|
|
Re: Revolver cleaning
[Re: InTim]
#188488
01/10/2018 2:38 AM
|
Joined: Oct 2013
Posts: 605
longhunter
addict
|
addict
Joined: Oct 2013
Posts: 605 |
"The reason a dog has so many friends,He wags his tail instead of his tongue."
"I don't always listen to Black Sabbath,But when I do so do the neighbors"
|
|
|
Re: Revolver cleaning
[Re: longhunter]
#188528
01/12/2018 2:22 PM
|
Joined: Dec 2005
Posts: 1,048
wvhitman
old hand
|
old hand
Joined: Dec 2005
Posts: 1,048 |
You'll see a thousand choices for inside maintainance. About all will work. For the exterior, I discovered GunBrite from Issos (at Midway) years ago. It's a paste that you apply, then wipe off. It cleans the surface and waterproofs it. My stainless guns look really clean before I treat them. When treated, the cloth is filthy. Blued guns are really impressive when treated. I do all guns twice a year and before any hunting trips. Never had any surface problems.
|
|
|
Re: Revolver cleaning
[Re: wvhitman]
#188855
01/21/2018 3:42 AM
|
Joined: Nov 2009
Posts: 1,642
BBwheelgunner
Pooh-Bah
|
Pooh-Bah
Joined: Nov 2009
Posts: 1,642 |
Thanks for the tip on the GunBrite,
looks like good stuff!
"If you are going to go through all the trouble to put a hole in something, why not make it a big one?"
|
|
|
Re: Revolver cleaning
[Re: BBwheelgunner]
#188856
01/21/2018 3:50 AM
|
Joined: Dec 2008
Posts: 4,861
Franchise
Distinguished Expert
|
Distinguished Expert
Joined: Dec 2008
Posts: 4,861 |
I just got some Gunbrite because Doc recommended it....my guns have NEVER been cleaner. That product is amazing!
The Eyes are Useless, When The Mind Is Blind
|
|
|
Re: Revolver cleaning
[Re: Franchise]
#189205
01/29/2018 1:33 AM
|
Joined: Jul 2017
Posts: 9
InTim
OP
stranger
|
OP
stranger
Joined: Jul 2017
Posts: 9 |
|
|
|
Re: Revolver cleaning
[Re: InTim]
#189211
01/29/2018 9:48 AM
|
Joined: Dec 2013
Posts: 378
BRASF0311
enthusiast
|
enthusiast
Joined: Dec 2013
Posts: 378 |
I've tried many of the wonder cleaners and lubes over the years and most do well, but I decided to save some money and use WD-40 to clean and white lithium grease for lube. Both of these can be found in Walmarts automotive section for under $4 a can, and they work well too. I also use a little steel wool wrapped around the bore brush to clean the chambers. I'm all for quick and easy.
|
|
|
Re: Revolver cleaning
[Re: BRASF0311]
#189255
01/30/2018 9:04 PM
|
Joined: Sep 2013
Posts: 4,669
Chance Weldon
Distinguished Expert
|
Distinguished Expert
Joined: Sep 2013
Posts: 4,669 |
I use Hoppe's for most of my cleaning jobs.
Formerly TN Lone Wolf
"We are only as strong as we are united, as weak as we are divided." - J.K. Rowling
|
|
|
Re: Revolver cleaning
[Re: Chance Weldon]
#189442
02/06/2018 4:15 AM
|
Joined: Sep 2012
Posts: 526
sw282
addict
|
addict
Joined: Sep 2012
Posts: 526 |
Kroil to clean.. Three in 0ne oil to lube
|
|
|
Re: Revolver cleaning
[Re: sw282]
#189627
02/11/2018 3:48 PM
|
Joined: Dec 2017
Posts: 34
DavT
newbie
|
newbie
Joined: Dec 2017
Posts: 34 |
Hoppes for solvent. The thing that helps me the most however is that I clean the cylinders in a Lyman Ultrasonic cleaner. I don't use the ultrasonic for any other parts but the cylinder come out perfect on my two FA Model 97's ( 45 colt and 357 ).
|
|
|
Re: Revolver cleaning
[Re: DavT]
#189629
02/11/2018 4:40 PM
|
Joined: Apr 2011
Posts: 89
cessna
journeyman
|
journeyman
Joined: Apr 2011
Posts: 89 |
DavT, I wonder what would happen if you put the cylinder from a SRH into a vibrating shell cleaner with the medium you use for cleaning brass. I use regular medium with no polish added. Interesting idea.
|
|
|
Re: Revolver cleaning
[Re: cessna]
#189630
02/11/2018 5:03 PM
|
Joined: Oct 2009
Posts: 2,556
junebug
Gun Slinger
|
Gun Slinger
Joined: Oct 2009
Posts: 2,556 |
DavT, I wonder what would happen if you put the cylinder from a SRH into a vibrating shell cleaner with the medium you use for cleaning brass. I use regular medium with no polish added. Interesting idea. You will get dust and media in places you don't want dust and media like under the star and inside the crane. Not a good idea.
Last edited by junebug; 02/11/2018 5:07 PM.
junebug
|
|
|
Re: Revolver cleaning
[Re: junebug]
#189633
02/11/2018 5:47 PM
|
Joined: Jan 2004
Posts: 9,608
s4s4u
Shootist
|
Shootist
Joined: Jan 2004
Posts: 9,608 |
DavT, I wonder what would happen if you put the cylinder from a SRH into a vibrating shell cleaner with the medium you use for cleaning brass. I use regular medium with no polish added. Interesting idea. You will get dust and media in places you don't want dust and media like under the star and inside the crane. Not a good idea. Agreed, and it might affect the finish as well. I wouldn't go there.
Rod, too.
Short cuts often lead to long recoveries.
|
|
|
Re: Revolver cleaning
[Re: s4s4u]
#189689
02/12/2018 5:18 PM
|
Joined: Apr 2011
Posts: 89
cessna
journeyman
|
journeyman
Joined: Apr 2011
Posts: 89 |
It was just a wild thought. I certainly wouldn't want to screw things up. Mostly I use Hoppe's on my revolvers.
|
|
|
|
0 registered members (),
50
guests, and 0
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|