|
Re: Step by step 357 project
[Re: dasbear]
#205742
02/25/2020 1:22 PM
|
Joined: May 2012
Posts: 2,508
reflex264
OP
Gun Slinger
|
OP
Gun Slinger
Joined: May 2012
Posts: 2,508 |
https://www.brownells.com/search/index.htm?k=ruger+latch&ksubmit=yDon't buy the over sized latch for your gun. A new factory latch and pin will tighten it up if your cylinder isn't badly worn. Can you take a good close up of the bolt tab on your latch and also measure it? The oversize latch in a stock gun/chambering can take a long time to fit correctly because it also affects timing. It is great to help control movement in a boomer especially when blocked for lateral movement.
"A quiet hit in the right place is better than a loud miss in the wrong place followed by 10 more shots on the run"
I was a handgun hunter, when handgun wasn't cool.....
|
|
|
Re: Step by step 357 project
[Re: 45MAN]
#205748
02/25/2020 5:45 PM
|
Joined: Jan 2004
Posts: 110
dasbear
member
|
member
Joined: Jan 2004
Posts: 110 |
DASBEAR: I BELIEVE REFLEX264 WAS DOING A REBUILD ON A WELL WORN OLDER REVOLVER. A NEWER REVOLVER CAN BE TWEAKED TO SHOOT BETTER WITH A LOT LESS WORK THAN A REBUILD. 45MAN As a complete novice to revolvers how does one determine wether a tweak or a complete teardown is necessary short of sending it off to a professional pistol smith and waiting for the sticker shock $$$ hammer to drop? I took an interest in this thread because I want the same end result as reflex264 2-4" at 100yds. If my 50.00 in parts + my time doesn't work out at least its cheap entertainment.
|
|
|
Re: Step by step 357 project
[Re: dasbear]
#205750
02/25/2020 7:11 PM
|
Joined: May 2012
Posts: 2,508
reflex264
OP
Gun Slinger
|
OP
Gun Slinger
Joined: May 2012
Posts: 2,508 |
DASBEAR: I BELIEVE REFLEX264 WAS DOING A REBUILD ON A WELL WORN OLDER REVOLVER. A NEWER REVOLVER CAN BE TWEAKED TO SHOOT BETTER WITH A LOT LESS WORK THAN A REBUILD. 45MAN As a complete novice to revolvers how does one determine wether a tweak or a complete teardown is necessary short of sending it off to a professional pistol smith and waiting for the sticker shock $$$ hammer to drop? I took an interest in this thread because I want the same end result as reflex264 2-4" at 100yds. If my 50.00 in parts + my time doesn't work out at least its cheap entertainment. Excessive cylinder movement is the biggest clue to wear problems.End shake, lateral movement and timing issues are usually a red flag. There are other things that aren't noticeable until the revolver is disassembled. I wish you were nearby. I would be glad to help get yours shooting. Once I get the whole process put together and posted it will make more sense. For the present issues and as bad as yours is shooting I would order the belt mountain pin, a new cylinder latch, latch and hammer pin. How is your trigger? It makes a difference as well.
"A quiet hit in the right place is better than a loud miss in the wrong place followed by 10 more shots on the run"
I was a handgun hunter, when handgun wasn't cool.....
|
|
|
Re: Step by step 357 project
[Re: reflex264]
#205887
03/07/2020 4:35 PM
|
Joined: Jan 2004
Posts: 110
dasbear
member
|
member
Joined: Jan 2004
Posts: 110 |
Sorry for the delay of info as multi tasking between gun projects has little to offer in completing either very quick. I recieved my parts for the RBH 41 cyl latch, cyl latch spring, 30oz trigger return spring, 19# hammer spring, cyl pin latch spring, pawl spring and belt mtn base pin. As mentioned the trigger and hammer had been done by my FIL at <3# pull the new 30 oz spring makes trigger feel mushy but I will test fire before replacing heavier return spring. A couple of setbacks to note cyl latch was over sized previously I was unaware so I reinstalled it(.090) the new latch measured .0875. 2nd issue BM base pin still too small the wobble is less but I feel can still be improved I most likely will go to a POWER CUSTOM base pin. After completing the assembly I measured head space at almost .007 (sb .002-.005?) Itook it down to .005 now barrel to cyl gap is .007 which will require sending gun out to have barrel set back to .002-.003. Anyone do feel free to comment if I took a wrong turn in my process I will be going out to test fire today but still need to reload for my 357 max contender before heading out.
|
|
|
Re: Step by step 357 project
[Re: dasbear]
#206011
03/17/2020 7:34 AM
|
Joined: Jan 2004
Posts: 110
dasbear
member
|
member
Joined: Jan 2004
Posts: 110 |
Made it out shooting this week with a 2x32 scope made it much easier on my eyes my best groups at 40 yds were about 1.5-2" 3 shots 2 touching with 1up or down in most groups which indicated inconsistent ignition. I was useing WLP PRIMERS so just to be sure I duplicated all loads with CCI LPM primers and went back out saturday with target set at 25yds and replacing 2x scope with a 2-7 burris made all the difference. Loads with 210gr xtp, H110 and 240gr LFNGC with H110 going 1/2-1inch at 25yds I will be posting pics soon just to make sure I'm not blowing smoke. Much thanks to reflex264 for showing how to bring old revolvers back to life
|
|
|
Re: Step by step 357 project
[Re: dasbear]
#206012
03/17/2020 10:53 AM
|
Joined: Aug 2017
Posts: 1,821
45MAN
Pooh-Bah
|
Pooh-Bah
Joined: Aug 2017
Posts: 1,821 |
Made it out shooting this week with a 2x32 scope made it much easier on my eyes my best groups at 40 yds were about 1.5-2" 3 shots 2 touching with 1up or down in most groups which indicated inconsistent ignition. I was useing WLP PRIMERS so just to be sure I duplicated all loads with CCI LPM primers and went back out saturday with target set at 25yds and replacing 2x scope with a 2-7 burris made all the difference. Loads with 210gr xtp, H110 and 240gr LFNGC with H110 going 1/2-1inch at 25yds I will be posting pics soon just to make sure I'm not blowing smoke. Much thanks to reflex264 for showing how to bring old revolvers back to life NICE, VERY NICE, ALWAYS GREAT TO GET GOOD GROUPS.
"ADAPT OR DIE". I USE ALL CAPS, NOT BECAUSE I AM YELLING, BUT BECAUSE IT IS AN OLD HABIT FROM MY ARMY DAYS, PLUS IT IS EASIER TO TYPE AND READ.
|
|
|
Re: Step by step 357 project
[Re: 45MAN]
#206034
03/17/2020 5:26 PM
|
Joined: Jan 2004
Posts: 110
dasbear
member
|
member
Joined: Jan 2004
Posts: 110 |
Ultimately velocity and accuracy are my goal because the Blackhawk will be used as a hunting handgun for bear and maybe blacktail deer.
|
|
|
Re: Step by step 357 project
[Re: dasbear]
#206066
03/18/2020 8:52 PM
|
Joined: May 2012
Posts: 2,508
reflex264
OP
Gun Slinger
|
OP
Gun Slinger
Joined: May 2012
Posts: 2,508 |
Certainly better! Definitely on the right track.
Hard to get anything done when you work. lol
"A quiet hit in the right place is better than a loud miss in the wrong place followed by 10 more shots on the run"
I was a handgun hunter, when handgun wasn't cool.....
|
|
|
Re: Step by step 357 project
[Re: reflex264]
#206090
03/20/2020 1:33 PM
|
Joined: Jan 2004
Posts: 110
dasbear
member
|
member
Joined: Jan 2004
Posts: 110 |
Certainly better! Definitely on the right track.
Hard to get anything done when you work. lol Someone told me once, when you get a bunch of guns you can retire and have fun I been trying my hand at that. lol Crap! I still gotta feed em all. Worse then kids I say.
|
|
|
|
0 registered members (),
444
guests, and 3
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|