Previous Thread
Next Thread
Print Thread
357 mag technical numbers needed #165370 10/30/2015 3:10 AM
Joined: Apr 2009
Posts: 3,625
Raptortrapper Offline OP
Shooting Master
OP Offline
Shooting Master
Joined: Apr 2009
Posts: 3,625
I have another buddy that wants to get into handgun hunting for next year. However, here in Colorado, we have to have a minimum of 550fpe at 50 yards to be legal. He might get a Colt Python that he wants to hunt with. He wants to shoot the 140gr leverevolution ammo through it for deer. Does anyone have the ACTUAL numbers on this ammo out of a 6" barrel? I need real velocity numbers, not "should be...." type of numbers.

The box gives info for an 18" rifle barrel, so it does us no good. Need to know the numbers out of a 6" barrel to find out if this ammo would be legal for him or not.

He has access to several boxes of it for a GREAT price if it works, so need to know for sure before buying it. So no speculation please. If it doesn't work, I told him about buffalo bore, and double tap, but this stuff would be a lot more expensive.

Yes, I told him about reloading, and he plans to do this, but right now, funds don't allow the purchase of the dillon press and all the components.

I'm hoping one of you has "been there and done that", and can give real numbers. I need the velocity you got, and from there, I can do the equation for the actual fpe.

Last edited by raptortrapper; 10/30/2015 3:14 AM.

A lot of people are like a slinky: Not much fun till you push them down the stairs!

Lifetime Member of the NRA! Wish I'd a done it sooner.
Re: 357 mag technical numbers needed [Re: Raptortrapper] #165376 10/30/2015 12:57 PM
Joined: Apr 2005
Posts: 6,963
KRal Offline
Shootist
Offline
Shootist
Joined: Apr 2005
Posts: 6,963
Unless your Game Officers carry around a chronograph, they're going to rely on the published data on the manufactures box.


It takes 43 muscles to frown and 17 to smile, but only 3 for proper trigger squeeze.
Re: 357 mag technical numbers needed [Re: KRal] #165378 10/30/2015 2:45 PM
Joined: Jan 2004
Posts: 4,155
Gregg Richter Offline
Distinguished Expert
Offline
Distinguished Expert
Joined: Jan 2004
Posts: 4,155
Back in the days when you had to pass a written test as well as a shooting test to hunt with a handgun in Colorado, I was a certified tester for the DOW. The hunter had to take the shooting test with a handgun that would meet the minimum requirements and we always considered the .357 magnum with heavy factory loads as legal.







Re: 357 mag technical numbers needed [Re: Gregg Richter] #165380 10/30/2015 4:15 PM
Joined: Apr 2009
Posts: 3,625
Raptortrapper Offline OP
Shooting Master
OP Offline
Shooting Master
Joined: Apr 2009
Posts: 3,625
Thanks guys. I checked with the local game warden that does my falconry stuff. He said if we have the information of what the chrony said, it would be good enough for him. Without it, he would have to have it tested himself.

Gregg-- the info on the box doesn't pertain to handguns, so what info is used at that point? Was it just automatically declared to be illegal? I don't think the leverevolution would classify as "heavy factory loads" though either. So maybe they aren't legal.

If we reload, the warden told us to keep a printout from a chrony that gave the velocities, and then have the bullet weight and the rest of the information on the inside label of the box. He actually told us, "If you reload, you essentially have 'factory ammo' that you created". He seemed pretty cool about the whole thing.

I've decided to help my buddy out, and get him set up for reloading with a bit of a loan, and then he can pay me back as he can. I figured if he is going to do this, might as well set him up for success as soon as possible rather than have a bunch of hoops for him to jump through.

He's excited, and that's half the battle.


A lot of people are like a slinky: Not much fun till you push them down the stairs!

Lifetime Member of the NRA! Wish I'd a done it sooner.
Re: 357 mag technical numbers needed [Re: Raptortrapper] #165385 10/30/2015 6:38 PM
Joined: Nov 2010
Posts: 1,101
Bearbait in NM Offline
old hand
Offline
old hand
Joined: Nov 2010
Posts: 1,101
Raptor,

I hopped on Youtube, and used "357 magnum leverevolution" as a search. I think the second video showed a guy with a 4" Taurus getting an average of 1352 fps at 12 yards. You should be able to find more videos, to get a warm fuzzy.

As an aside, what your Game Officer told you kinda worried me. He said you need the print-out from the chrony. I do not have a printer for my chrony, and while it has been a few years since hunting in Colorado, it is not a "never again" kind of thing.

Craig


Northern born and Southern bred
Re: 357 mag technical numbers needed [Re: Raptortrapper] #165399 10/31/2015 1:11 AM
Joined: Jan 2004
Posts: 4,155
Gregg Richter Offline
Distinguished Expert
Offline
Distinguished Expert
Joined: Jan 2004
Posts: 4,155
 Originally Posted By: raptortrapper
Thanks guys. I checked with the local game warden that does my falconry stuff. He said if we have the information of what the chrony said, it would be good enough for him. Without it, he would have to have it tested himself.

Gregg-- the info on the box doesn't pertain to handguns, so what info is used at that point? Was it just automatically declared to be illegal? I don't think the leverevolution would classify as "heavy factory loads" though either. So maybe they aren't legal.

If we reload, the warden told us to keep a printout from a chrony that gave the velocities, and then have the bullet weight and the rest of the information on the inside label of the box. He actually told us, "If you reload, you essentially have 'factory ammo' that you created". He seemed pretty cool about the whole thing.

I've decided to help my buddy out, and get him set up for reloading with a bit of a loan, and then he can pay me back as he can. I figured if he is going to do this, might as well set him up for success as soon as possible rather than have a bunch of hoops for him to jump through.

He's excited, and that's half the battle.


Paul, you are getting kudos from me for starting out another handgun hunter.

My posting said that we testers and the DOW generally decided that factory .357 mag hunting loads were LEGAL, not illegal as you wrote. The point was "Let's not split hairs."

It bothers me that your particular DOW guy is coming across as a hair splitter. I hope that I am wrong, but for him to make the statement about the handloads that "he would have to have it tested himself" is exactly that: splitting hairs.

Does he not have any better things to do as in catching REAL POACHERS??? Sorry, but this seems out of line.

JMHO

PS: What if the "chrono" shows "only" 495 FPE? Don't we all know that it is more important to put it in the right spot?

\:\)


The DOW officers should be much more concerned about the guy who buys his new rifle (of course it was bore-sighted, right?) and then goes out hunting without really testing it himself. Yes...this happens and I have witnessed it personally many times over.

Maybe the rifle hunters should have to pass a "shooting test."
But something tells me that would hurt license sales!

;\)







Re: 357 mag technical numbers needed [Re: Gregg Richter] #165403 10/31/2015 7:12 PM
Joined: Apr 2009
Posts: 3,625
Raptortrapper Offline OP
Shooting Master
OP Offline
Shooting Master
Joined: Apr 2009
Posts: 3,625
Yeah I hear ya Gregg. He can be a hair splitter at times. You mentioned heavy loads, that's why I took it to mean that the leverevolution wouldn't qualify. I don't really consider those to be heavy loads at all. Not even close. I guess I misunderstood what you were saying.

I've got a call in to him about this specific ammo, and he is looking into it to see if it would be allowed or not.

Craig-- I would imagine if a person had the numbers written down, it would be just as good. But then again, this is Colorado, and I have yet to meet 2 game wardens that interpret things the same way. My falconry stuff is the same way. One warden tells me I have to have rabbits skinned and gutted in the freezer. Another tells me I have to have them gutted, but the skin can stay on. Yet another in Eastern Colorado tells my buddy they can be frozen with guts in and hair still on.

Haven't met anyone that has actually been nailed for rabbits frozen incorrectly, but just sayin....


A lot of people are like a slinky: Not much fun till you push them down the stairs!

Lifetime Member of the NRA! Wish I'd a done it sooner.
Re: 357 mag technical numbers needed [Re: Raptortrapper] #165405 10/31/2015 7:36 PM
Joined: Jan 2004
Posts: 4,155
Gregg Richter Offline
Distinguished Expert
Offline
Distinguished Expert
Joined: Jan 2004
Posts: 4,155


That is funny...







Re: 357 mag technical numbers needed [Re: Gregg Richter] #165439 11/01/2015 3:11 PM
Joined: Nov 2010
Posts: 1,101
Bearbait in NM Offline
old hand
Offline
old hand
Joined: Nov 2010
Posts: 1,101
Paul,

I am all to familiar with the "arbitrariness" with the Game Officers in Colorado. I went round and round with them over shooting off the hood of my Jeep. That one caused me to shoot my chrony, as I was so mad about the incident, I lost focus, flinched, and center punched the chrony. I had officers interpret that particular law 4 ways. Sitting in a vehicle shooting, one foot on the ground while sort of sitting in the vehicle, two feet on the ground, and this guy, any part of the gun touching the vehicle.

Back to your original query, something else that came to me yesterday while running some warm loads through my Colt NF 45. I had Peacemaker Specialists cut a 357 mag cylinder to 45 Colt for the gun. They used tight chamber mouth specs of 0.452. The factory throats were .456-.458. The exact same loads in both cylinders have the tighter throated cylinder shooting about 120 fps faster, at the chrony. I ran the numbers, and the original cylinder would not make the 550/50, whereas the tighter one does. I would say that any gun caliber that is close to the line will need to be individually tested.

If I ever decide to use a handgun in Colorado again, rather than using this Colt or any of my 45 Super or Rowland pistols/revolvers that can make it with handloads, I would probably just use my FA 454. My thought being that an officer would see the 454 Headstamp, and not even give the ammo a second thought. Which would be ironic, as my FA would probably be downloaded a bit.

Craig


Northern born and Southern bred
Re: 357 mag technical numbers needed [Re: Bearbait in NM] #165449 11/01/2015 8:25 PM
Joined: Apr 2009
Posts: 3,625
Raptortrapper Offline OP
Shooting Master
OP Offline
Shooting Master
Joined: Apr 2009
Posts: 3,625
Yeah I hear ya Craig. I talked to this same game warden and asked if 45 Colt was legal. He didn't even hesitate, and said it was. I didn't bother telling him that 45 Colt can be loaded WAAAAAY down to levels that are most likely not legal.

I wish they were more educated about our handguns, but at the same time, I don't really want to bring it up to them.


A lot of people are like a slinky: Not much fun till you push them down the stairs!

Lifetime Member of the NRA! Wish I'd a done it sooner.
Re: 357 mag technical numbers needed [Re: Raptortrapper] #165452 11/01/2015 10:41 PM
Joined: Jun 2008
Posts: 650
wheeler45 Offline
addict
Offline
addict
Joined: Jun 2008
Posts: 650
F.P.E? F.P.S.? In Indiana it does not matter. To be legal the handgun must be a 4-15.9 inch barrel, bullet diameter .243 inch minimum, case length 1.16 inch minimum. Neck a .357 magnum case down to .243 and presto! This makes the .256 Winchester a legal deer cartridge, but the 10mm is not. Our rifle rules are also based on case dimensions and bullet diameters. The C.O.s carry case gauges. I have been teaching Hunter Education classes for 23 years and met only one C.O. who reloaded or understood ballistics.


I can do all things through Christ which strengtheneth me. Phil. 4:13
Re: 357 mag technical numbers needed [Re: Bearbait in NM] #165453 11/01/2015 11:05 PM
Joined: Jan 2004
Posts: 9,608
s4s4u Offline
Shootist
Offline
Shootist
Joined: Jan 2004
Posts: 9,608
 Quote:
My thought being that an officer would see the 454 Headstamp, and not even give the ammo a second thought.


Maybe a person should trim 454 cases to use in the 45 Colt..... ;-)


Rod, too.

Short cuts often lead to long recoveries.
Re: 357 mag technical numbers needed [Re: s4s4u] #165454 11/01/2015 11:18 PM
Joined: Sep 2013
Posts: 4,669
Chance Weldon Offline
Distinguished Expert
Offline
Distinguished Expert
Joined: Sep 2013
Posts: 4,669
This makes me glad I live in Tennessee. Our big game handgun hunting regulations are it must be a centerfire cartridge, and you must be 18 or older. Kind of hard to fall out of line in this state.


Formerly TN Lone Wolf

"We are only as strong as we are united, as weak as we are divided." - J.K. Rowling
Re: 357 mag technical numbers needed [Re: Chance Weldon] #165461 11/01/2015 11:58 PM
Joined: Aug 2014
Posts: 2,209
REDHAWK1954 Offline
Pooh-Bah
Offline
Pooh-Bah
Joined: Aug 2014
Posts: 2,209
North Carolina is about the same as TN.


Michael Joe Moore
Re: 357 mag technical numbers needed [Re: REDHAWK1954] #165466 11/02/2015 12:31 AM
Joined: Sep 2012
Posts: 526
sw282 Offline
addict
Offline
addict
Joined: Sep 2012
Posts: 526
Here in SC the law reads ''Any center fire cartridge''.

Sure am glad my .25 Baby Browning is still legal for Deer

Re: 357 mag technical numbers needed [Re: sw282] #165482 11/02/2015 2:18 PM
Joined: Nov 2010
Posts: 1,101
Bearbait in NM Offline
old hand
Offline
old hand
Joined: Nov 2010
Posts: 1,101
S4,

Now that there is a heck of an idea. The thing is, I do make sure I am at the legal minimum, so I would not not be in violation, by the letter of the law.

SW, that is good, as if you come to NM, you can also shoot elk with your Baby Browning. At least our state is a little smart. Legally you could shoot deer with a 22LR, but they know elk are bigger, so it has to be .243. So you are good to go.

Paul, that really shows that your warden sort of has no clue. The SAAMI 45 Colt will absolutely not make it, nor any ammo you would likely find on a store shelf. I think I hunted maybe 10 or so years in Colorado, and probably got check for something, 8 or 9 times. Been doing it 16 years in NM, and have never even seen a Game Officer in the field, much less been checked for anything. Been stopped a bunch down on the border hunting javelina, but those were always fed's, and they never went beyond seeing my non-hispanic looking face.

Craig


Northern born and Southern bred
Re: 357 mag technical numbers needed [Re: Bearbait in NM] #165487 11/02/2015 4:32 PM
Joined: Apr 2009
Posts: 3,625
Raptortrapper Offline OP
Shooting Master
OP Offline
Shooting Master
Joined: Apr 2009
Posts: 3,625
Yeah I hear ya Craig. I get stopped a lot when I'm in the field with my falconry stuff simply because I get people calling in to the DOW saying, "There's a guy with a eagle in the field". So they have to come say hi. We laugh about it, and move on. Happens at least two or three times a season. Granted, Anaya is a large Red Tailed Hawk, but she's not even CLOSE to eagle size.

Part of me is glad that people care enough about wildlife to call in and have an officer check things out. Another part of me just wishes people would mind their own dang business.

I realise falconry isn't something ya see every day, so I'm probably gonna get called in now and then. But I've only been checked a few times while fishing, and maybe twice while hunting here in Colorado. Always have everything with me, so it basically ends up being a short conversation and "how's the family doing" type of a stop. I'm the only falconer around these parts, so I've gotten to know the game wardens here pretty well. Makes it nice in a way.

Last edited by raptortrapper; 11/02/2015 4:35 PM.

A lot of people are like a slinky: Not much fun till you push them down the stairs!

Lifetime Member of the NRA! Wish I'd a done it sooner.
Re: 357 mag technical numbers needed [Re: Raptortrapper] #165488 11/02/2015 5:06 PM
Joined: Sep 2015
Posts: 211
Sam86 Offline
enthusiast
Offline
enthusiast
Joined: Sep 2015
Posts: 211
in KS the law now states "center fired and not fully automatic" so much for my full auto 22LR pistol hunt lol

Re: 357 mag technical numbers needed [Re: Raptortrapper] #165826 11/11/2015 9:57 PM
Joined: Feb 2004
Posts: 1,280
Sawfish Offline
veteran
Offline
veteran
Joined: Feb 2004
Posts: 1,280
 Originally Posted By: raptortrapper
I have another buddy that wants to get into handgun hunting for next year. However, here in Colorado, we have to have a minimum of 550fpe at 50 yards to be legal. He might get a Colt Python that he wants to hunt with. He wants to shoot the 140gr leverevolution ammo through it for deer. Does anyone have the ACTUAL numbers on this ammo out of a 6" barrel? I need real velocity numbers, not "should be...." type of numbers.

The box gives info for an 18" rifle barrel, so it does us no good. Need to know the numbers out of a 6" barrel to find out if this ammo would be legal for him or not.

He has access to several boxes of it for a GREAT price if it works, so need to know for sure before buying it. So no speculation please. If it doesn't work, I told him about buffalo bore, and double tap, but this stuff would be a lot more expensive.

Yes, I told him about reloading, and he plans to do this, but right now, funds don't allow the purchase of the dillon press and all the components.

I'm hoping one of you has "been there and done that", and can give real numbers. I need the velocity you got, and from there, I can do the equation for the actual fpe.


Is the Python cylinder long enough to accommodate the Flex Tip ammo?

Last edited by Sawfish; 11/11/2015 9:58 PM.

Good Shooting Makes Good Hunting
Patron Member NRA;
Life Member RMEF, SCI, NSRPA, CRPA: Member, FTRF, HHI #7108, CBA

Moderated by  Chance Weldon, Gary, Gregg Richter 

Newest Members
Redhawk41, Striker243, Sxviper, RobbieD, IRONMAN
9668 Registered Users
Top Posters(30 Days)
karl 1
Who's Online Now
0 registered members (), 54 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
Powered by UBB.threads™ PHP Forum Software 7.7.3