Should I drill and tap a 686-3??
#208957
11/09/2020 11:00 PM
|
Joined: Dec 2019
Posts: 154
RBO21
OP
member
|
OP
member
Joined: Dec 2019
Posts: 154 |
I have a S&W 686-3 that I like shooting. I would like to hunt with it more than I do, but would feel more comfortable using a reflex sight on it. Would I ruin the value? It has already been Magna Ported by the previous owner, so not exactly original anyway.
|
|
|
Re: Should I drill and tap a 686-3??
[Re: RBO21]
#208958
11/09/2020 11:22 PM
|
Joined: Apr 2009
Posts: 3,625
Raptortrapper
Shooting Master
|
Shooting Master
Joined: Apr 2009
Posts: 3,625 |
This makes me cry. But since it's already been abused, might as well make it work for ya. Lot of guys like the reflex sight for sure. I've never used one.
A lot of people are like a slinky: Not much fun till you push them down the stairs!
Lifetime Member of the NRA! Wish I'd a done it sooner.
|
|
|
Re: Should I drill and tap a 686-3??
[Re: Raptortrapper]
#208997
11/12/2020 2:05 AM
|
Joined: Nov 2019
Posts: 218
gunslingerdad
enthusiast
|
enthusiast
Joined: Nov 2019
Posts: 218 |
if you want to shoot it more go for it. if it already ported it isnt going to hurt the value.
still Dave Thomas, just an alias so the gov't dont find me
|
|
|
Re: Should I drill and tap a 686-3??
[Re: gunslingerdad]
#209044
11/13/2020 5:43 PM
|
Joined: Apr 2005
Posts: 6,963
KRal
Shootist
|
Shootist
Joined: Apr 2005
Posts: 6,963 |
No need to drill and tape. Get you a Weigand mini mount and hit the woods.
It takes 43 muscles to frown and 17 to smile, but only 3 for proper trigger squeeze.
|
|
|
Re: Should I drill and tap a 686-3??
[Re: KRal]
#209049
11/13/2020 6:26 PM
|
Joined: Jan 2004
Posts: 9,715
jamesfromjersey
Shootist
|
Shootist
Joined: Jan 2004
Posts: 9,715 |
No need to drill and tape. Get you a Weigand mini mount and hit the woods.
Life member-NRA-SCI Member-HHI #2900-HHASA #067 Colt-Ruger-Freedom Arms-and S&W Collector Assoc.s "I have more guns then I need but not as many as I want" "Handgun hunters HAVE to be good"
|
|
|
Re: Should I drill and tap a 686-3??
[Re: jamesfromjersey]
#209175
11/20/2020 2:07 PM
|
Joined: Dec 2019
Posts: 154
RBO21
OP
member
|
OP
member
Joined: Dec 2019
Posts: 154 |
I thought the mini mount still required you to drill and tap. I'll take a look.
|
|
|
Re: Should I drill and tap a 686-3??
[Re: RBO21]
#209180
11/21/2020 3:04 AM
|
Joined: Nov 2019
Posts: 218
gunslingerdad
enthusiast
|
enthusiast
Joined: Nov 2019
Posts: 218 |
should mount in the rear sight hole
still Dave Thomas, just an alias so the gov't dont find me
|
|
|
Re: Should I drill and tap a 686-3??
[Re: gunslingerdad]
#209213
11/23/2020 9:41 PM
|
Joined: Feb 2004
Posts: 1,280
Sawfish
veteran
|
veteran
Joined: Feb 2004
Posts: 1,280 |
Weigand website has a complete description on the mounting.
Good Shooting Makes Good Hunting Patron Member NRA; Life Member RMEF, SCI, NSRPA, CRPA: Member, FTRF, HHI #7108, CBA
|
|
|
Re: Should I drill and tap a 686-3??
[Re: Sawfish]
#209308
11/29/2020 1:01 PM
|
Joined: Oct 2008
Posts: 750
bluecow
old hand
|
old hand
Joined: Oct 2008
Posts: 750 |
JMHO! We worry way too much about the value,the next generation, preserving guns original whatever..... Unless its a vary rare or historical firearm then bend, twist, chop, modify to your hearts content. Make it into what you want. What makes Colt 1st gen SAA so valuable is that most where used and used hard for years (BTW thats what they where made for). If we took every new S&W 6somethingorother-whattoheck and locked em away, 75 years from now they wouldn't have any great value.
I'll take my soap box and go home now, thanks
Everything before "but" is B.S.
|
|
|
Re: Should I drill and tap a 686-3??
[Re: bluecow]
#209425
12/04/2020 8:05 PM
|
Joined: Feb 2004
Posts: 1,280
Sawfish
veteran
|
veteran
Joined: Feb 2004
Posts: 1,280 |
If you prefer drilling and tapping have your gunsmith drill and tap your gun just like S&W does on its newer factory models. The factory rear sight is removed and the holes are drilled in the sight channel. If you want to change back to iron sights, remove the scope and replace the iron sight. If done properly, the holes will not show. I had a Model 27 done like this, and it works great.
Good Shooting Makes Good Hunting Patron Member NRA; Life Member RMEF, SCI, NSRPA, CRPA: Member, FTRF, HHI #7108, CBA
|
|
|
Re: Should I drill and tap a 686-3??
[Re: Sawfish]
#209458
12/06/2020 7:15 PM
|
Joined: Jan 2004
Posts: 9,715
jamesfromjersey
Shootist
|
Shootist
Joined: Jan 2004
Posts: 9,715 |
If you prefer drilling and tapping have your gunsmith drill and tap your gun just like S&W does on its newer factory models. The factory rear sight is removed and the holes are drilled in the sight channel. If you want to change back to iron sights, remove the scope and replace the iron sight. If done properly, the holes will not show. I had a Model 27 done like this, and it works great. Marvin says it all above
Life member-NRA-SCI Member-HHI #2900-HHASA #067 Colt-Ruger-Freedom Arms-and S&W Collector Assoc.s "I have more guns then I need but not as many as I want" "Handgun hunters HAVE to be good"
|
|
|
Re: Should I drill and tap a 686-3??
[Re: jamesfromjersey]
#209724
12/18/2020 7:44 PM
|
Joined: Nov 2015
Posts: 190
short30
member
|
member
Joined: Nov 2015
Posts: 190 |
also concur, see BB as I D&T'd under factory site and installed Weigand, worked with reddot for me - mine was a well used 4 inch that I had bought then sold then went back and re-bought from a friend - it was just too good to let get away.
First Handgun Deer: ~1982 8" S&W .38Spl SW 7.5" 686-7 with Matchdot II SBHH .45LC 7.5" Contender G2 .35-30/30 (Bellm), .22LR, .22 Hornet, 25-35 Glock 40 10mm; G21 Poly80 w/ 9 inch barrel (in work)
|
|
|
|
0 registered members (),
108
guests, and 0
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|